-
Forum
-
Antique Caterpillar Machinery Owners Club
-
FOR SALE/WANTED
-
WTB Ten parts
WTB Ten parts
Less
More
-
Posts: 190
-
Thank you received: 0
-
11 years 7 months ago #85139
by jdkoller
Does anyone have a Ten dash and a couple trunion nuts they might want to part with? If so, please PM me.
Thanks,
Jamie
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 871
-
Thank you received: 13
-
11 years 7 months ago #85151
by Cysco
Jamie,
The previous owner had welded nuts on to the axle to cover other issues on my Ten. Fortunatly I had a box of misc parts and found two.....I will look through it today and see if there is by chance one or two more.
What other parts are you needing ?
Have a good day....Bill
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 190
-
Thank you received: 0
-
11 years 7 months ago #85168
by jdkoller
I still need hard to find items like bottom radiator tank, support, mag coupler cover ignition switch and key.
Aside form that, I'm about ready to start sand blasting.
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 252
-
Thank you received: 0
-
Less
More
-
Posts: 190
-
Thank you received: 0
-
11 years 7 months ago #85352
by jdkoller
Clarification, I have discovered that my late model dash is different from early model Tens. I am looking for a dash with "heat on" and "heat off" labeled on it. As opposed to hot/cold.
Thanks
Jamie
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 190
-
Thank you received: 0
-
11 years 6 months ago #86519
by jdkoller
Refreshing post....
I'm still looking for a repairable bottom radiator support, ignition switch and key.
I'll probably end up repairing the dash and radiator tank I have but the support is too far gone.
Wally, thanks for all the parts so far.
Jason, thanks for all of the advice so far.
Jamie
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 82
-
Thank you received: 3
-
11 years 6 months ago #86523
by sandman
Jamie,
If you could use just the center for your radiator support I have a few. See in the pic the middle
part that I have cast. I get $75. for one.
Thanks, Karl 530-533-2266 <a href="
This email address is being protected from spambots. You need JavaScript enabled to view it." target="_blank">
This email address is being protected from spambots. You need JavaScript enabled to view it.
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 190
-
Thank you received: 0
-
11 years 6 months ago #86683
by jdkoller
Where do I find bellow seals and the gasket that goes with?
Also, I assume there is a seal on the front transmission shaft. I should probably replace that while I have it apart?
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 737
-
Thank you received: 0
-
11 years 6 months ago #86689
by WyoCat
Your bellows looks good. I would just put new cork on them. I get precut cork form Olson's. Order it by Cat part #.
Chad Enyeart
Please Log in or Create an account to join the conversation.
Less
More
-
Posts: 3879
-
Thank you received: 4
-
-
Forum
-
Antique Caterpillar Machinery Owners Club
-
FOR SALE/WANTED
-
WTB Ten parts
Time to create page: 0.185 seconds
Jamie,