acmoc

ACMOC Membership Benefits

  • FREE quarterly magazine filled with content about antique Caterpillar machines
  • FREE classified listings
  • ACMOC store discounts and specials
  • Full Bulletin Board Access
    • Marketplace (For Sale/Wanted)
    • Technical Library
    • Post attachments

$44 /year ELECTRONIC

$60 /year USA

$77 /year International

D13000

More
17 years 4 months ago #7632 by charles poole
D13000 was created by charles poole
Ol magnet , If you read this post , could you possibly give me any information you might have , I have a D13000 power unit serail # 4s13531 , bill of matl #
9B2998 , If you could even give me the year of this engine iI would appreciate it !! thanks , charles poole

Please Log in or Create an account to join the conversation.

More
17 years 4 months ago #7633 by Old Magnet
Replied by Old Magnet on topic D13000
Looks to be at the end of the 4S series.
I show 13,279 - up and 1953 production.

I have the Operator's Instructions manual 4S1001 - up Diesel Engine and Electric Set but not the Parts Manual.

What information are you looking for?

Please Log in or Create an account to join the conversation.

More
17 years 4 months ago #7639 by SJ
Replied by SJ on topic D13000
As far as horse power there are so many settings for this engine that the RPMs & the rack setting would have to be determined to even establish what it is. My old Cat fuel injection book has a 1/2 page of different settings for that particular engine. AS far as a parts book the old D8 2U tractor had the same basic engine so most parts are all the same except a few minor differences.

Please Log in or Create an account to join the conversation.

More
17 years 4 months ago #7647 by charles poole
Replied by charles poole on topic D13000
Thank you , ol magnet & SJ the two of you seem to be the men to go to when
it comes to these motors , I will be communicating with the two of you soon , maybe with some pictures , thanks again chas !!!

Please Log in or Create an account to join the conversation.

More
17 years 4 months ago #7684 by charles poole
In addition to restoring a 38 b shovel with a caterpillar engine , I am also restoring a unit model 614 cable backhoe ,with a 2-71 detroit , I have completely rebuilt the engine , But now I am having trouble locating drive chains
they are 3 .25 inch pitch roller , does anyone out there have any idea where I might locate some ?? Thanks , chas

Please Log in or Create an account to join the conversation.

More
17 years 4 months ago #7685 by SJ
Replied by SJ on topic Chain
You could give this place a call & see if they can help you or steer you to a place. It,s Bearings & Drives Unlimited, 1568 Highway 315 Wilkes Barre Pa. Ph. (570) 822-7196

Please Log in or Create an account to join the conversation.

More
17 years 4 months ago #7686 by Craneman
Replied by Craneman on topic D13000
Try Roland Machinery at 800-765-2635 and tell them that you want Ray Heffernaum to contact you. Roland Machinery is a Komatsu Dealer but they also sell Pyramid Parts. Pyramid crane chain cost a little more than the competitors but it's the best drive chain made..it's built heavier/beefier than than anybody elses. Once Pyramid chain is installed they'll be no more breaking pins or links.

Please Log in or Create an account to join the conversation.

More
17 years 4 months ago #7695 by charles poole
Replied by charles poole on topic D13000
Thanks SJ ,and craneman , I appreciate the info !!
Thanks again , Chas

Please Log in or Create an account to join the conversation.

More
17 years 4 months ago #7934 by charles poole
Replied by charles poole on topic D13000
Hi all , Brought my engine into a shop where i can work on it at night or during
bad weather , I had pulled the heads off this engine last summer while it was still in the shovel , I thought that I just had a stuck engine caused by water going down the exhaust , As it turns out there is a little more to it than that !!
I disconnected 3 connecting rods and pulled 3 sleeves pistons intact ,
Apparently someone had tried to turn this engine over with I believe water in cylinder As I found # 4 con rod severely bent ,and about a two inch chip out of the bottom of the sleeve ,the good news is the crank journals appear to be OK ,
I will try to pull the remaining 3 tomorrow .
I am starting to think I know how paso chris feels !!

Please Log in or Create an account to join the conversation.

More
17 years 4 months ago #7935 by Old Magnet
Replied by Old Magnet on topic D13000
Three down and three to go:D :D Not bad so far....hope Chris is observing cause he's about to face the same issues (less bent rod I hope)
Please share your techniques:) :)

Please Log in or Create an account to join the conversation.

Time to create page: 0.166 seconds
Go to top