HomeJoin / RenewChaptersEventsMembersForumAbout
ScholarshipsMachinesDonateYouTube Watch HereGet the FREE Newsletter
acmoc

ACMOC Membership Benefits

  • FREE quarterly magazine filled with content about antique Caterpillar machines
  • FREE classified listings
  • ACMOC store discounts and specials
  • Full Bulletin Board Access
    • Marketplace (For Sale/Wanted)
    • Technical Library
    • Post attachments

$44 /year ELECTRONIC

$60 /year USA

$77 /year International

  1. Forum
  3. Antique Caterpillar Machinery Owners Club
  5. FOR SALE/WANTED
  7. Wanted...pony motor controls

Wanted...pony motor controls

More
8 years 10 months ago #136265 by Hillbillybjopkr
Wanted...pony motor controls was created by Hillbillybjopkr
looking for the choke and throttle rods for a pony on a D4-7U...that are straight and properly labled....mine are both bent and both say choke

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #136282 by rax200
Replied by rax200 on topic Knobs
Hi Hillbillybjopkr, The knobs are still available from Cat, Choke is 3b5017 and the Throttle is 3b5016. As for the rods i would straighten them out as they are hard to get.

Regards
Daryl
Daryl

1937 RD4 4G4368
1940 D4 7J3717
1942 D4 7J9915SP
1942 R4 6G2550SP
1944 D4 2T6584SP
1945 D4 2T8978SP
1946 D4 5T6271
1956 D4 7U37855
1954 DH226 S/N 89 Howard Tug

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #136286 by ag-mike
Replied by ag-mike on topic Wanted...pony motor controls
uhh,,,,, the rods are suppose to be bent
My channel www.youtube.com/channel/UC9XkaV0X15FyObT...ideos?view_as=public

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #136434 by Hillbillybjopkr
Replied by Hillbillybjopkr on topic Wanted...pony motor controls
don't think the throttle rod is suppost to be bent 90 degrees right at the knob lol

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #136482 by STEPHEN
Replied by STEPHEN on topic Wanted...pony motor controls

don't think the throttle rod is suppost to be bent 90 degrees right at the knob lol


Sounds like an easy fix then, but don't bend it cold. If the end gets snapped off, the rod can be added to as well.

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #136844 by Hillbillybjopkr
Replied by Hillbillybjopkr on topic Wanted...pony motor controls
...I might need to add a little anyways.....sparkplug keeps zappin me if I get to close lol......side note....magneto works REALLY well lol

Please Log in or Create an account to join the conversation.

More
8 years 10 months ago #136909 by drujinin
Replied by drujinin on topic Wanted...pony motor controls
If the Mag is zapping you, then you are doing it right! :pound: :wave:
LOL!
Actually it only proves its good on one side, now go over and check the other side! :eyebrows: :pound:

Please Log in or Create an account to join the conversation.

More
8 years 8 months ago #139411 by Bothborn52
Replied by Bothborn52 on topic Wanted...pony motor controls

looking for the choke and throttle rods for a pony on a D4-7U...that are straight and properly labled....mine are both bent and both say choke


I know that the pony motors are the same for D4 and D2 but I don't know about the throttle and choke rods. These are off of a D2 5U.
Attachments:

Please Log in or Create an account to join the conversation.

  1. Forum
  3. Antique Caterpillar Machinery Owners Club
  5. FOR SALE/WANTED
  7. Wanted...pony motor controls
Time to create page: 0.156 seconds
Go to top