- Posts: 737
- Thank you received: 0
ACMOC Membership Benefits
- FREE quarterly magazine filled with content about antique Caterpillar machines
- FREE classified listings
- ACMOC store discounts and specials
- Full Bulletin Board Access
- Marketplace (For Sale/Wanted)
- Technical Library
- Post attachments
$44 /year ELECTRONIC
$60 /year USA
$77 /year International
Pony carb float needed
11 years 7 months ago #85586
by WyoCat
Chad Enyeart
Pony carb float needed was created by WyoCat
Does anyone know a good source for a replacement float for the 22AX8 down draft zenith pony carbs? Carb number is 10322 from an early D8. Thanks in advance.
Chad Enyeart
Please Log in or Create an account to join the conversation.
- Old Magnet
-
- Offline
- Platinum Boarder
- Member
Less
More
- Posts: 16722
- Thank you received: 814
11 years 7 months ago #85587
by Old Magnet
Replied by Old Magnet on topic Pony carb float needed
Please Log in or Create an account to join the conversation.
11 years 7 months ago #85593
by WyoCat
Chad Enyeart
Replied by WyoCat on topic Pony carb float needed
Thanks for the reply OM. That sure says it will work, but it doesn't even look close. The original float has 2 float chambers. I wonder if this was an updated float that only needed one side to work.
Chad Enyeart
Please Log in or Create an account to join the conversation.
- Old Magnet
-
- Offline
- Platinum Boarder
- Member
Less
More
- Posts: 16722
- Thank you received: 814
11 years 7 months ago #85594
by Old Magnet
Replied by Old Magnet on topic Pony carb float needed
That's a no go.....actually takes a zenith C85-68-S...Cat #9B4921 and it is a dual float unit.
Vender is showing wrong unit but might be worth a call to get the right one.
Try Florin tractor parts, their web parts search says they have 125 of them.
Vender is showing wrong unit but might be worth a call to get the right one.
Try Florin tractor parts, their web parts search says they have 125 of them.
Please Log in or Create an account to join the conversation.
11 years 7 months ago #85601
by WyoCat
Chad Enyeart
Replied by WyoCat on topic Pony carb float needed
I wanted to call Florin, but did not have a cat part number. Thanks for all of your help OM!
Chad Enyeart
Please Log in or Create an account to join the conversation.
- Jason 10/D4
-
- Offline
- Platinum Boarder
- User
Less
More
- Posts: 482
- Thank you received: 0
11 years 7 months ago #85635
by Jason 10/D4
Replied by Jason 10/D4 on topic Pony carb float needed
is there numbers on the float i have a whole bag full of decent floats but not sure of what they fit. Jason
Please Log in or Create an account to join the conversation.
11 years 7 months ago #85637
by WyoCat
Chad Enyeart
Replied by WyoCat on topic Pony carb float needed
Jason,
No numbers at all on it. Must of had water in it at some point cause it is crushed in on itself really badly.
Florin had the part in stock. I ordered 2 of them so I had one for my stock. They are on their way!
No numbers at all on it. Must of had water in it at some point cause it is crushed in on itself really badly.
Florin had the part in stock. I ordered 2 of them so I had one for my stock. They are on their way!
Chad Enyeart
Please Log in or Create an account to join the conversation.
Time to create page: 0.148 seconds
ACMOC
Antique Caterpillar Machinery Owners Club
1115 Madison St NE # 1117
Salem, OR 97301
support@acmoc.org
Become a Member!
"I became a member recently because the wealth of knowledge here is priceless."
- Chris R
"I also joined a year ago. had been on here a couple of times as a non-member and found the info very helpful so I got a one year subscription (not very expensive at all) to try it out. I really like all the resources on here so I just got a three year. I think its a very small price for what you can get out of this site."
- Jason N