Wanted: Ensign 2A1516 Carburetor Parts

Al Ayotte
Topic Author
Offline
New Boarder
User

11 years 7 months ago #85543 by Al Ayotte

Wanted: Ensign 2A1516 Carburetor Parts was created by Al Ayotte

Can someone tell me where I can find carburetor parts for my CAT Diesel 35 pony motor? Specifically, I need a
9B7902 Control (Fuel)?

Thanks

Al Ayotte

D4 7U; CAT DIESEL 35; CAT 22; CAT 30 (Wide Gauge)

Please Log in or Create an account to join the conversation.

Steve A
Offline
Platinum Boarder
Member

11 years 7 months ago #85770 by Steve A

Replied by Steve A on topic part

Good Morning

What Dad is looking for is the round cylinder piece thats made out of pot metal, the threads that hold the high speed rod are gone, Dennis wilkinson ( omni track) used to sell these so somebody must make them. we need some direction

Please Log in or Create an account to join the conversation.

WyoCat
Offline
Platinum Boarder
User

11 years 7 months ago #85773 by WyoCat

Replied by WyoCat on topic Wanted: Ensign 2A1516 Carburetor Parts

I can probably help you out. I would need to know if your carb is the low fuel bowl or the high fuel bowl.

Chad Enyeart

Please Log in or Create an account to join the conversation.

Steve A
Offline
Platinum Boarder
Member

11 years 7 months ago #85774 by Steve A

Replied by Steve A on topic ID

Chad
I know there is a long and a short refering to the cylinder piece, I can measure dads,mine are all the same including 2 bad ones I have.

Is there a simple wat to tell looking at the top of the carb

Please Log in or Create an account to join the conversation.

WyoCat
Offline
Platinum Boarder
User

11 years 7 months ago #85782 by WyoCat

Replied by WyoCat on topic Wanted: Ensign 2A1516 Carburetor Parts

If it is the high fuel bowl design it would have a fairly rounded top with all of the ensign letters and wording cast onto it. The low bowl design has a flatter look. All of the writing would have been on a small brass tag. They are commonly missing but you can see 2 small bumps in the flat spot on the top about the size of a pin head. That's where the brass tag would have been.

Chad Enyeart

Please Log in or Create an account to join the conversation.

Al Ayotte
Topic Author
Offline
New Boarder
User

11 years 7 months ago #85791 by Al Ayotte

Replied by Al Ayotte on topic Re: Ensign Carburetor parts

"WyoCat" wrote:
If it is the high fuel bowl design it would have a fairly rounded top with all of the ensign letters and wording cast onto it. The low bowl design has a flatter look. All of the writing would have been on a small brass tag. They are commonly missing but you can see 2 small bumps in the flat spot on the top about the size of a pin head. That's where the brass tag would have been.

Chad: My Carb is the high bowl design. The control measures 1.75" long and has "VC" stamped on the bottom.

Al Ayotte

D4 7U; CAT DIESEL 35; CAT 22; CAT 30 (Wide Gauge)

Please Log in or Create an account to join the conversation.

WyoCat
Offline
Platinum Boarder
User

11 years 7 months ago #85837 by WyoCat

Replied by WyoCat on topic Wanted: Ensign 2A1516 Carburetor Parts

Al, I sent you a PM with my phone number.

Chad Enyeart

Please Log in or Create an account to join the conversation.

ACMOC

Antique Caterpillar Machinery Owners Club

1115 Madison St NE # 1117
Salem, OR 97301

support@acmoc.org

Chapters History Events Members Contact

Member Quick Links:

Store Forum

Become a Member!

"I became a member recently because the wealth of knowledge here is priceless."
- Chris R

"I also joined a year ago. had been on here a couple of times as a non-member and found the info very helpful so I got a one year subscription (not very expensive at all) to try it out. I really like all the resources on here so I just got a three year. I think its a very small price for what you can get out of this site."
- Jason N

ACMOC Membership Benefits

$44 /year ELECTRONIC

$60 /year USA

$77 /year International

Wanted: Ensign 2A1516 Carburetor Parts

ACMOC