- Posts: 35
- Thank you received: 0
ACMOC Membership Benefits
- FREE quarterly magazine filled with content about antique Caterpillar machines
- FREE classified listings
- ACMOC store discounts and specials
- Full Bulletin Board Access
- Marketplace (For Sale/Wanted)
- Technical Library
- Post attachments
$44 /year ELECTRONIC
$60 /year USA
$77 /year International
for ccjersey subject d4
17 years 1 month ago #9824
by clogs
for ccjersey subject d4 was created by clogs
ccjersey is it possible to post part nos for head gaskets,exhaust valves, top and bottem gasket velve chest, piston rings, and the gasket between the main cylinder head and the water jacket on pony moter
many thanks in anticipation clogs
many thanks in anticipation clogs
Please Log in or Create an account to join the conversation.
- Old Magnet
-
- Offline
- Platinum Boarder
- Member
Less
More
- Posts: 16724
- Thank you received: 818
17 years 1 month ago #9828
by Old Magnet
Replied by Old Magnet on topic for ccjersey subject d4
This should cover it.
Please Log in or Create an account to join the conversation.
17 years 1 month ago #9832
by ccjersey
D2-5J's, D6-9U's, D318 and D333 power units, 12E-99E grader, 922B & 944A wheel loaders, D330C generator set, DW20 water tanker and a bunch of Jersey cows to take care of in my spare time:D
Replied by ccjersey on topic for ccjersey subject d4
clogs,
OM has you fixed up on the gaskets and valves. I don't have a book for the D4. D2 5J is as close as I can come, but should be same engine.
On the rings, have you measured the piston and bore? Lots of those old pony engines have been bored to oversize, sleeved back to standard etc. Until you get in there, you probably won't know for sure what you have.
OM has you fixed up on the gaskets and valves. I don't have a book for the D4. D2 5J is as close as I can come, but should be same engine.
On the rings, have you measured the piston and bore? Lots of those old pony engines have been bored to oversize, sleeved back to standard etc. Until you get in there, you probably won't know for sure what you have.
D2-5J's, D6-9U's, D318 and D333 power units, 12E-99E grader, 922B & 944A wheel loaders, D330C generator set, DW20 water tanker and a bunch of Jersey cows to take care of in my spare time:D
Please Log in or Create an account to join the conversation.
- Old Magnet
-
- Offline
- Platinum Boarder
- Member
Less
More
- Posts: 16724
- Thank you received: 818
17 years 1 month ago #9833
by Old Magnet
Replied by Old Magnet on topic for ccjersey subject d4
Be aware that on this early a pony the later 7B rods may not interchange with the 2A rods. The later rods are a thicker cross section and have been known to interfere with the cylinder skirts.
Please Log in or Create an account to join the conversation.
17 years 1 month ago #9873
by clogs
Replied by clogs on topic clogs d4 to old magnate
thanks for diagramme would you happen to have part nos for piston rings
many thanks for your help clogs
many thanks for your help clogs
Please Log in or Create an account to join the conversation.
- Old Magnet
-
- Offline
- Platinum Boarder
- Member
Less
More
- Posts: 16724
- Thank you received: 818
17 years 1 month ago #9882
by Old Magnet
Replied by Old Magnet on topic for ccjersey subject d4
Nothing unique about rings. Can be had from any supplier that sells rings by dimensions such as
www.hastingsmfg.com
Please Log in or Create an account to join the conversation.
Time to create page: 0.152 seconds
ACMOC
Antique Caterpillar Machinery Owners Club
1115 Madison St NE # 1117
Salem, OR 97301
support@acmoc.org
Become a Member!
"I became a member recently because the wealth of knowledge here is priceless."
- Chris R
"I also joined a year ago. had been on here a couple of times as a non-member and found the info very helpful so I got a one year subscription (not very expensive at all) to try it out. I really like all the resources on here so I just got a three year. I think its a very small price for what you can get out of this site."
- Jason N