Early 6 - 7 U parts numbers needed

cr

Topic Author

Offline

Member

Send a private message to cr

Posts: 646

Thank you received: 25

.

Please log in or create an account to join the conversation.

Mon, Mar 3, 2014 8:18 AM

josh

Offline

Send a private message to josh

Posts: 1,238

Thank you received: 13

Shaft is 4B7298 and bushing is 5F0209. This is the bushing in the clutch lever, and shaft on the shifter housing.

Please log in or create an account to join the conversation.

Mon, Mar 3, 2014 9:17 AM

Old Magnet

Offline

Send a private message to Old Magnet

Posts: 16,787

Thank you received: 48

Reply to josh:

Shaft is 4B7298 and bushing is 5F0209. This is the bushing in the clutch lever, and shaft on the shifter housing.

Just going through changing one of these myself. Florin tractor showed the shaft in stock but not the bushing. I wound up making my own shaft and bored out the lever and shift tower to use a standard size shaft and bushing.

Also there is a little known and not shown in the parts book replacement shift tower 8F8075 that allows use of the later boot 8F8079, which is available aftermarket from Florin.

Please log in or create an account to join the conversation.

Mon, Mar 3, 2014 1:25 PM

chriscokid

Offline

Send a private message to chriscokid

Posts: 3,341

Thank you received: 0

i have done this many times, just make a new shaft and bushing, you will have it done before you can even order the parts and it will be alot cheaper too!

Please log in or create an account to join the conversation.

Mon, Mar 3, 2014 6:49 PM

Old Magnet

Offline

Send a private message to Old Magnet

Posts: 16,787

Thank you received: 48

Reply to chriscokid:

i have done this many times, just make a new shaft and bushing, you will have it done before you can even order the parts and it will be alot cheaper too!

Never could figure out why Cat used an odd ball diameter shaft and bushing there....0.889" dia. if I remember right. Easy change to 1" dia.
Used a "Nomex" bushing that does not require lube. Will see how it works out.

Please log in or create an account to join the conversation.

Mon, Mar 3, 2014 10:53 PM

d9gdon

Offline

Send a private message to d9gdon

Posts: 889

Thank you received: 4

That's a good looking helper, obviously giving it the QC look over.👍

Please log in or create an account to join the conversation.

Sat, Mar 8, 2014 7:22 PM

neil

Offline

Member

Moderator

Admin

Super Admin

Send a private message to neil

Posts: 7,272

Thank you received: 61

Reply to d9gdon:

That's a good looking helper, obviously giving it the QC look over.👍

Yep, glad to see the Quality Control inspector is giving it a thorough going-over. I'm "sure" there was no bed-time candy bribery going on, at all! : )

Please log in or create an account to join the conversation.

Sat, Mar 8, 2014 8:10 PM

Mike Meyer

Offline

Member

Send a private message to Mike Meyer

Posts: 3,337

Thank you received: 6

Reply to neil:

Yep, glad to see the Quality Control inspector is giving it a thorough going-over. I'm "sure" there was no bed-time candy bribery going on, at all! : )

Good photo's CR, it's always great to see our kids involved.
regards
Mike

Please log in or create an account to join the conversation.

Sun, Mar 9, 2014 1:32 AM

ag-mike

Offline

Send a private message to ag-mike

Posts: 1,687

Thank you received: 0

Reply to Mike Meyer:

Good photo's CR, it's always great to see our kids involved.
regards
Mike

Machinist or operator in training? good luck with ur project.

Please log in or create an account to join the conversation.

Sun, Mar 9, 2014 4:14 AM

Early 6 - 7 U parts numbers needed

Follow Us on Social Media

Upcoming Events

Testimonials