ACMOC
Login
ACMOC
cat 12 -8t blade dropping. when arms are at horizontal

cat 12 -8t blade dropping. when arms are at horizontal

Showing 1 to 2 of 2 results
oldbeek
Topic Author
Offline
Member
Send a private message to oldbeek
Posts: 781
Thank you received: 0
The later 12s have a brake band and drum on the shaft from the control box. BUT the older 12s dont. If blade is dropping when the arms are horizontal what do you do on an early 8t. Worm gear and bull gear are in  good shape. You can lift the front end without kicking.
Please log in or create an account to join the conversation.
Sun, Sep 3, 2023 6:36 AM
Deas Plant.
Offline
Member
Send a private message to Deas Plant.
Location: Currently - DowNunda.
Posts: 6,716
Thank you received: 31
Hi, oldbeek.
I would suggest that first place to look would be the bearing adjustment for the worm gear that drives the bull gear on the back end of the horizontal blade lift shaft. I can't remember what adjustment the 8Ts had, whether screw and lock nut or the earlier cap and shims arrangement. Either way, you need to have a little weight on the lift arm to be able set the bearing clearance 'coz that pulls the worm inboard into the inner bearing leaving all the clearance at the outer bearing.

DO NOT over-tighten this bearing or the control lever will boot you through the back of the cab or throw you through the windshield.

Another thing that can cause the dropping is severely worn teeth on the blade lift bull gear which is the big one on the front of the cab,

That said, pretty much all of this stuff is in this post:

https://www.acmoc.org/bb/discussion-d72/11465-home-at-last#91423

Hope this helps.

Just my 0.02.

You have a wonderful day. Best wishes. Deas Plant.

Please log in or create an account to join the conversation.
Sun, Sep 3, 2023 7:06 AM
Deas Plant.
Offline
Member
Send a private message to Deas Plant.
Location: Currently - DowNunda.
Posts: 6,716
Thank you received: 31
Reply to Deas Plant.:
Hi, oldbeek.
I would suggest that first place to look would be the bearing adjustment for the worm gear that drives the bull gear on the back end of the horizontal blade lift shaft. I can't remember what adjustment the 8Ts had, whether screw and lock nut or the earlier cap and shims arrangement. Either way, you need to have a little weight on the lift arm to be able set the bearing clearance 'coz that pulls the worm inboard into the inner bearing leaving all the clearance at the outer bearing.

DO NOT over-tighten this bearing or the control lever will boot you through the back of the cab or throw you through the windshield.

Another thing that can cause the dropping is severely worn teeth on the blade lift bull gear which is the big one on the front of the cab,

That said, pretty much all of this stuff is in this post:

https://www.acmoc.org/bb/discussion-d72/11465-home-at-last#91423

Hope this helps.

Just my 0.02.
Hi, oldbeek.
If the above doesn't work, the next thing I'd be looking at would the amount of wear on the blade lift bull gear in the area where the worm drive engages it when the arm is horizontal. This would involve marking the lift shaft so that you know when you have that section up to the inspection plug opening at the top, loosening the lift arm clamps, removing the key and rotating the bull gear and shaft until those teeth come to the top where you can inspect them.

(You might need to remove the inspection opening plug in the top of the housing to be able to see the bull gear teeth. LOL.)

Just my 0.02.

You have a wonderful day. Best wishes. Deas Plant.

Please log in or create an account to join the conversation.
Mon, Sep 4, 2023 1:44 PM
Showing 1 to 2 of 2 results
YouTube Video Placeholder

Follow Us on Social Media

Our channel highlights machines from the earliest Holt and Best track-type tractors, equipment from the start of Caterpillar in 1925, up to units built in the mid-1960s.

Upcoming Events

Newby Hall Tractor Fest

Chapter Two

| Newby Hall, Ripon, Noth Yorkshire, HG4 5AJ

High Weald Steam Working Weekend

Chapter Two

| Freshfield Farm, Sloop Lane, Scaynes Hill RH17 7NP UK

Sibbertoft Annual Muck Shifting Weekend

Chapter Two

| Avalanche adventure, Welford Rd, Sibbertoft LE16 9UJ, UK

Cromford Steam Rally

Chapter Two

| Highacres Farm, Dewey Lane, Brackenfield, Derbyshire DE55 6DB, UK
View Calendar
ACMOC

Antique Caterpillar
Machinery Owners Club

1115 Madison St NE # 1117
Salem, OR 97301

[email protected]

Terms & Privacy
Website developed by AdCo

Testimonials

"I also joined a year ago. had been on here a couple of times as a non-member and found the info very helpful so I got a one year subscription (not very expensive at all) to try it out. I really like all the resources on here so I just got a three year. I think its a very small price for what you can get out of this site."
-Jason N

Join Today!