- Posts: 84
- Thank you received: 0
ACMOC Membership Benefits
- FREE quarterly magazine filled with content about antique Caterpillar machines
- FREE classified listings
- ACMOC store discounts and specials
- Full Bulletin Board Access
- Marketplace (For Sale/Wanted)
- Technical Library
- Post attachments
$44 /year ELECTRONIC
$60 /year USA
$77 /year International
2009 show
- gwhdiesel75
-
- Offline
- Platinum Boarder
- User
Less
More
- Posts: 1585
- Thank you received: 1
16 years 1 month ago #21563
by gwhdiesel75
Replied by gwhdiesel75 on topic 2009 show
Yes. Canandaigua, New York, in upstate near Rochester.
Please Log in or Create an account to join the conversation.
16 years 1 month ago #21565
by drujinin
Replied by drujinin on topic Anybody have a date?
For the 2009 show in New York?
Is that at the Gas and Steam show grounds?
Is that at the Gas and Steam show grounds?
Please Log in or Create an account to join the conversation.
- gwhdiesel75
-
- Offline
- Platinum Boarder
- User
Less
More
- Posts: 1585
- Thank you received: 1
16 years 1 month ago #21575
by gwhdiesel75
Replied by gwhdiesel75 on topic 2009 show
Yes, right off U.S. Route 20 I think. It is the same place we had the last Canandaigua show. It will be a large show with a lot of equipment, as it always is there. And it is in Jeff Huff's neighborhood, so he can bring over some of his equiupment too from the museum.
GWH
GWH
Please Log in or Create an account to join the conversation.
16 years 1 month ago #21579
by drujinin
Replied by drujinin on topic Oil Patch equipment
It would be neat if they could get Messers (?) to bring back and setup all the oil patch equipment that they had there at the September Gas and Steam show this year. This stuff is what I grew up around out there on the Pennsy border. The wife and I were on vacation out there in September and got to see the annual show.
Please Log in or Create an account to join the conversation.
- terrywelch_archive
-
- Offline
- Platinum Boarder
- User
Less
More
- Posts: 768
- Thank you received: 5
16 years 1 month ago #21584
by terrywelch_archive
Replied by terrywelch_archive on topic 2009 show
I would like to see the Fairbanks, Samson and a few other tractors that are near there. I am hoping we can get a crew to go out there for the show.
Terry
Terry
Please Log in or Create an account to join the conversation.
16 years 1 month ago #21856
by cdw
If fuel stays down there should be a good showing from New England there again. I will be taking at least 3 tractors and one of my pull graders. I would like to get my 66 pull grader there but I am going to need more trailer deck than I have if i am planning to get two tractors on with the grader. I hope George will come back to his old stomping grounds.
Please Log in or Create an account to join the conversation.
- gwhdiesel75
-
- Offline
- Platinum Boarder
- User
Less
More
- Posts: 1585
- Thank you received: 1
16 years 1 month ago #21874
by gwhdiesel75
Replied by gwhdiesel75 on topic 2009 show
Oh, I wouldn't miss that show for anything! I will see you there, God willing. GWH
Please Log in or Create an account to join the conversation.
Time to create page: 0.178 seconds
ACMOC
Antique Caterpillar Machinery Owners Club
1115 Madison St NE # 1117
Salem, OR 97301
support@acmoc.org
Become a Member!
"I became a member recently because the wealth of knowledge here is priceless."
- Chris R
"I also joined a year ago. had been on here a couple of times as a non-member and found the info very helpful so I got a one year subscription (not very expensive at all) to try it out. I really like all the resources on here so I just got a three year. I think its a very small price for what you can get out of this site."
- Jason N